Marble shooting crossbow

A few months after having built my home made crossbow I had an idea for building one that would shoot marbles.

This was in the mid 80s, when I was still a teenager living out in the country. My dad still had some narrower strips of spring steel that I hadn't used up with my other crossbow. These wouldn't be strong enough to throw an arrow really hard, but for much lighter projectiles they'd be just right.

I staggered the steel bands, with one long one furthest to the front, and successively shorter ones behind that one (a bit like leaf springs in a car). I have more bands near the middle, where the bending moment on the bow is the greatest, and just one band extending all the way to the end which moves the fastest. The idea was to keep the ends of the bow light, so that there would be less inertia in the bow, and thus more of the inertia given to the marble.

The crossbow will put a marble through the thin plywood that nectarine crates are made of and also through 1970s style fake interior wood paneling. If I use a 5/8" steel ball instead of a marble it will make a very clean hole in 1/4" plywood.

At the time that I built it (back in 1986), my options for measuring the projectile speed were very limited - basically, no media capable computers and digital cameras existed, and I didn't even have an oscilloscope. But I measured the speed of the projectile by shooting a marble up into a ball of plasticine. The marble became stuck in the plasticine, and I measured how high the plasticine ball was thrown up. From that, I was able to calculate its speed, and thus its momentum, and from the weight of the plasticine and the marble, I was able to calculate how fast the marble must have hit the ball to give it that momentum.

The muzzle velocity with marbles is 67 meters per second, which it turned out, worked out to 150 mph even (I don't use MPH normally, but I remembered that figure because it worked out so evenly). That's way out of slingshot territory, but still only about half as fast as the marble shooting airgun I built 17 years later.

The catch with marbles is that there's no place to hook a string onto them, so inevitably the string would jump over the marble or the marble would jump out of the track.

The solution I tried was to have a track both above and below the marble. This kept the marble in place and also prevented the string from jumping over the marble.

I wasn't at all sure whether this would work when I started, but it was worth a try. Surprisingly, it actually worked. I might have used slightly better wood if I had known that it would work when I started!

I used the same double hook as in my previous crossbow, figuring this way I could still hook an arrow onto it. It wasn't possible to start the marble all the way back against the string, because the track that the marble runs in didn't extend in between the hooks. But even so, there wasn't a noticeable problem.

You can see the string getting frayed, as usual. I had originally used two tightly wound strands of baler twine, but didn't have any of that available last time I replaced the string. So I braided together three groups of strands from those super strong white straps that are often tied around shipping crates. The braiding really helped in that it keeps the frayed parts from separating from the main bundle. That in turn slows down further fraying.

Here's a view of the hooks and trigger. The trigger is the lever near the handle. Its pushed up to trigger. This allows the block with the hooks on it to turn counter-clockwise, releasing the string. You can see the head of the nail that I used as a shaft for the hook block to pivot on.

I ran into a bit of a problem whenever I was aiming at something on the ground. With the run aimed downward the marble would start rolling and fall out the muzzle without me having shot it. So I added this strip of metal to sort of clip it in place at the end of the track. The strip pivots on a screw and is pushed down by a spring stretched over it.

On the inside of the top track it protrudes into the track just a bit - enough to keep the marble from rolling out. The momentum of dropping the marble in the muzzle gives it enough momentum to overcome the friction that this bit of metal causes so that it ends up behind it. I had to add a screw to limit the strip from coming too far down, and another to keep it from getting thrown too far up when a shot is made.

It's not nearly as accurate as the sight on a rifle, but then again neither is the crossbow, so the sight is more than adequate.

See also:

My other homemade crossbow

Homemade marble shooting air gun

Jenga pistol

Potato cannons

Marble machine 2.1

Back to my Woodworking website